Have you been searching for advice concerning How to Install a Bathtub?
Setting up a bath tub isn't precisely brain surgery, however it does require solid plumbing, carpentry, and often, tiling skills. Replacing an old tub with a new one is additionally a moderately hard job. If the old tub is easily accessible, the project can relocate speedily; if you need to open up a wall to get rid of the old tub as well as place the new bathtub, the task is much harder. In either situation, the job is within a residence handyman's abilities, although you will certainly need an assistant to vacate the old bathtub as well as set in the new one. Make sure you have actually qualified on your own for the work and are comfortable trying it. As opposed to working with a service provider to take over a halfway-completed job, it is much better to consider using one prior to you start. Chances are you may require a professional plumber to make tube links.
This short article will aid you install a new tub in your shower room if you have already gotten a brand-new bathtub as well as do not require to alter the arrangement of your previous water supply pipelines.
Your tools and also product checklist must comprise the following:
Preparing for the Installment
First of all, the supporting frame supplied with the bathroom should be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to make sure that if the tap comes with a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps system to prevent stress on the bath tub.
Fit the versatile tap ports to the bottom of both taps making use of 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet via the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you make use of all of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom ought to now be ready to be suited its final setting.
Removing Old Taps
If you require to change old taps with new ones as a part of your setup, after that the first thing you ought to do is detach the water system. After doing so, activate the taps to drain any water staying in the system. The procedure of eliminating the existing faucets can be fairly bothersome due to the restricted access that is often the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric ready for the staying water that will originate from the pipelines. When the supply pipes have been removed, make use of the exact same device to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from turning throughout this procedure. When the taps have actually been eliminated, the holes in the bath/basin will have to be cleaned up of any kind of old sealing compound.
Prior to moving on to fit the brand-new taps, contrast the pipe connections on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.
Mounting the Bathtub
Utilizing both wood boards under its feet, place the tub in the needed placement. The wooden boards are valuable in evenly spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 tiny factors.
The next objective is to make certain that the bathtub is leveled all round. This can be achieved by checking the spirit level and also changing the feet on the tub until the spirit level reads degree.
To install faucets, fit all-time low of the outermost versatile faucet adapter to the suitable supply pipeline by making a compression sign up with; after that do the exact same for the other tap.
Switch on the water as well as inspect all joints and brand-new pipework for leakages and tighten them if essential. Fill the tub as well as likewise examine the overflow outlet and also the normal outlet for leaks.
Ultimately, repair the bathroom paneling as described in the manufacturer's user's manual. Tiling as well as securing around the bath tub must wait until the bathtub has actually been used at the very least once as this will settle it right into its last position.
Fitting New Touches
If the tails of the new taps are plastic, then you will certainly require a plastic connector to prevent damages to the string. One end of the adapter fits on the plastic tail of the tap and also the other end supplies a connection to the current supply pipelines.
If you require to fit a monobloc, then you will certainly need lowering couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the placing opening in the bath/basin making certain that the washing machines remain in location in between the faucet as well as the sink. Secure the faucet in position with the supplier given backnut. When the tap is securely in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical faucet adapters. The previous kind ought to be attached to the tap finishes initially, tightening up just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the location where the bath meets the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to break an inflexible seal, causing the water to permeate the wall surface in between the bath and the tiling, resulting in issues with dampness and also possible leakages to the ceiling below.
You can pick from a range of coloured sealants to blend in your components as well as fittings. They are marketed in tubes and also cartridges, as well as are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of soaked paper or soft rope. Bear in mind to always fill the bathtub with water prior to sealing, to enable the activity experienced when the tub is in usage. The sealer can crack relatively early if you do not take into account this movement prior to securing.
Alternatively, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise easily available on the marketplace. It is a good idea to fit the tiles using water-resistant or waterproof glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy more info about How to Install a Bathtub? Make feedback down the page. We'd be glad to see your insights about this write up. Hoping to see you back again later on. Are you aware of another person who is fascinated with Installing A Bathtub? Feel free to share it. Thank you for taking the time to read it.
Dial, rest easy!